Preparation and study of mechanical and thermal properties of an epoxy composites with isobutyl rubber
Damaged water taps powder and signals
Keywords:
epoxy, isobutyl rubber, thermal conductivity, mechanical propertiesAbstract
Through this research, polymeric composites were prepared from epoxy as a base material with isobutyl rubber (waste rubber washers powder for water taps) and this was done by adding different weight percentages of isobutyl rubber. This was done by adding different weight percentages of isobutyl rubber. After a series of experiments, it was found that the best weight percentage was (5%).This addition was done at different temperatures (8,25,55) °C. The results when compared before and after the reinforcement process for the composites showed that the thermal conductivity decreased after the reinforcement process, as for the resistance to hardness and compressibility, it increased after reinforcement, but it was less valuable for the hardness and compressibility at the temperature (55) °C compared to the results at (8) °C. As for the shock resistance, its value increased after reinforcement, and the increase was greater at the temperature (55) °C compared to its value at (8) °C.
Downloads
References
Al-Mousawi, Ali Ibrahim “The effect of reinforcement with Mgo particles on the thermal and mechanical properties of epoxy resin” The Iraqi Journal of Mechanical and Materials Engineering, Volume 11, Issue 3, 2011.
Dr.Hani (2008) “Mechanical properties of composite material using Natural Rabber with Epoxy Risen” Technical college ALMusaib.
Al-Mayali, Khaleda Hussein, (2010) “The effect of ultrasound on some rheological and mechanical properties of Buna synthetic rubber” University of Kufa, College of Education for Girls, Department of Physics, Iraq
Al-Rawi, Khaled Rashad, Salman, Rebekah Amer, (2014) “Studying some mechanical properties of the Epoxy_Mgo composite” University of Baghdad, College of Science for Girls, Department of Physics, Iraq.
Ahmad, Adnan, Seif, Abdul Majeed, Moayyed, (2017) “A practical study of some mechanical and physical properties of a binary polymer mixture of (epoxy-polyurethane)” Tikrit Journal of Engineering Sciences, Volume 24, Issue 2.
Muhammad, Abdul Rahman Rashid, (2019) “Studying the effect of direction, volume fractures and temperature on the flexural strength property of polymeric sheets reinforced with glass fibers” Al-Qadisiyah University, College of Education, Department of Physics, Iraq
Al-Rawi, Rua’a Essam, (2019) “Studying some mechanical and physical properties of an epoxy composite reinforced with glass and carbon fibers.” Master’s thesis, University of Mosul, College of Education for Girls, Department of Chemistry.
Ibrahiem, R.E, Sulyman, E, Z “ Preparation of polymeric composites from Epoxy with Randomly woven Fiber Glass and Studies the Mechanical properties “Ravidain ,Journal of science 28.3(2019)
D .Hull, (1981) “An Introduction to composite Material” Cambridge university press first published in
Waad Allah, Esraa Saad, (2020) “Preparation and study of some mechanical and thermal properties of unsaturated polyester with polyethylene and fluorescent powder” Master’s thesis, University of Mosul, College of Education for Girls, Department of Chemistry.
Al-Hadidi, Jaafar Taher, (1990) "Engineering materials, an introduction to their properties and applications" University of Technology
Shukla, shankla Prasad (2011) “Investigation into tribo potential of rice husk(RH) char reinforced epoxy composite” M.Sc.Thesis, Deemed University, National institute of technology India.P.7.
Al_Jeebory,AA, Al-Mosawi AI,Abdul Allah,SA,(2009) “Effect of percentage of Fibers Reinforcement on Thermal and Mechanical properties for polymeric composite materials” Iraqi Journal of Mechanical and Materials Engineering special Issue , first conference of Engineering collage, BaBylon University.
Akram, Sinai, (2009) “Measuring the thermal conductivity of epoxy and unsaturated polyester composites reinforced with hybrid layers of calcareous and carbon fibers” University of Baghdad, College of Science, Department of Physics, Iraq.
Naglaa, Abdel Nour, Fadel, Ali, (2013) “Measuring the thermal change of polyester resin composites.” With different weight ratios, "The Iraqi Journal of Mechanical Engineering and Materials Engineering Sio2 Unsaturated after adding Volume 13, Issue 2.
Published
How to Cite
Issue
Section
Copyright (c) 2022 International journal of health sciences
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Articles published in the International Journal of Health Sciences (IJHS) are available under Creative Commons Attribution Non-Commercial No Derivatives Licence (CC BY-NC-ND 4.0). Authors retain copyright in their work and grant IJHS right of first publication under CC BY-NC-ND 4.0. Users have the right to read, download, copy, distribute, print, search, or link to the full texts of articles in this journal, and to use them for any other lawful purpose.
Articles published in IJHS can be copied, communicated and shared in their published form for non-commercial purposes provided full attribution is given to the author and the journal. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
This copyright notice applies to articles published in IJHS volumes 4 onwards. Please read about the copyright notices for previous volumes under Journal History.
